As the centrepiece of any modern bathroom, the basin taps should be both stylish and functional, enhancing the overall aesthetic and providing ease of use. The introduction of mono basin mixer tap has revolutionised how we use our sinks, offering a seamless, one-handle operation that delivers hot and cold water in one go. If you’re looking to upgrade your bathroom with a sleek and contemporary basin mixer tap, let us guide you through the process of installing one at home.
In this step-by-step guide, we’ll break down everything you need to know about installing a mono basin mixer tap. We’ll cover all the basic aspects of the installation, from removing the old tap and preparing the sink to fitting the new unit and testing its functionality. Whether you’re a seasoned DIY enthusiast or a beginner looking to take on a new challenge, our guide to installing a mono basin mixer tap at home will provide you with the knowledge and confidence to
1. Tools and Materials Needed for Installation
Before beginning the installation of a mono basin mixer tap, gathering all of the necessary tools and materials is essential. The following tools will be required for a successful installation:
- An adjustable wrench
- A basin spanner
- A flathead screwdriver
- A Phillips head screwdriver
- A spirit level
- A silicone sealant gun
Additionally, it is imperative to have the appropriate materials on hand, such as a mono basin mixer tap with all necessary fixtures and fittings, a basin waste kit, and PTFE tape. Taking the time to ensure that all tools and materials are available and in good condition, before beginning the installation will help to ensure a smooth and efficient process.
2. Turning off the Water Supply and Removing the Old Tap
The second step in installing a mono basin mixer tap at home involves turning off the water supply and removing the old tap. Before starting this step, ensure that you have all the necessary tools, including adjustable spanners, pliers, a basin wrench, and a cloth or towel to clean up any spills. Start by locating the stop valves that control the flow of hot and cold water to the basin. Turn them off by twisting the levers or handles clockwise until they are in the off position.
Next, loosen the nuts or bolts that secure the old tap to the basin using a spanner or pliers. If the tap is stuck, you may need to use a basin wrench to help remove it. Carefully lift the old tap out of the basin and place it aside. Use a cloth or towel to remove any excess water or debris around the tap hole. With the old tap removed, you are now ready to move on to the next step in the installation process.
3. Attaching the New Mono Basin Mixer Tap
Attaching the new mono basin mixer tap is critical in successfully installing a new tap in your bathroom sink. Begin by unscrewing the nuts that come with the tap kit from the tail pipes of the tap. Then, position the tap over the holes in your basin and ensure that it sits at the centre of the basin.
You can then tighten the nuts over the tail pipes using an adjustable wrench, ensuring the tap is securely attached to the basin. It is important to avoid over-tightening the nuts to avoid damaging the basin or any washers in the assembly. Once you have completed this step, check for leaks by running water through the tap to ensure there are no leaks or drips, and tighten the nuts further if necessary.
4. Connecting Water Supply and Testing for Leaks
The fourth step in installing a mono basin mixer tap is connecting the water supply and testing for leaks. First, turn off the main water supply and drain any residual water from the pipes to prevent contamination. Next, attach the flexible tap connectors to the tap tails and secure them with spanners, ensuring they are not over-tightened to avoid damage.
Fit the washers and nuts on the opposite end of the connectors to the isolation valves, again using spanners to tighten. Finally, turn on the water supply and slowly open the valve to allow the water to flow through the system. Inspect for any leaks in the connections and tighten any loose fittings as required. This crucial final step will ensure the proper functioning of the tap and prevent any unnecessary water wastage or damage.
5. Final Adjustments and Clean Up
Before tightening the nuts and bolts to their final position, ensure the tap is aligned correctly and levelled with the basin. This is done by gently adjusting the position of the tap until it’s in the desired position.
Once the tap is level, use a spanner to securely tighten the nuts and bolts. Next, use a damp cloth to wipe away any excess caulk or silicone that may have spread during installation. Finally, turn on the water supply and run the tap to ensure that it’s working properly and there are no leaks. Congratulations, you can now enjoy your new mono basin mixer tap!
Conclusion
Installing a mono basin mixer tap at home may seem daunting, especially if you’re unfamiliar with plumbing. However, with the right tools, instructions, and a bit of patience, anyone can successfully install their own tap. Following the step-by-step guide outlined in this post will ensure a smooth and efficient installation process. Not only will you save money on plumbing costs, but you’ll also have the satisfaction of a job well done and a stylish new upgrade to your bathroom or kitchen.
We hope you found this blog post on Installing a Mono Basin Mixer Tap at Home – A Step-by-Step Guide useful. Be sure to check out our post on Kitchen Faucets: A Few Features That Can Make Your Purchase Useful for more great tips!
Have Experience in the Moving Industry? Want an Additional Income Stream? Work With All Around Moving!
Partner with All Around Moving and join the Work With Us program. We’ll help you make money arranging moving services, by establishing your own moving consultant business operation. Read the simple terms by Clicking here to learn more.
